Manual zz. BiPAC Series Warning Do not open or repair the case yourself. If the BiPAC Series is too hot, turn off the power immediately and have it repaired at a qualified service center. Avoid using this product and all accessories outdoors.

Author:Gogor Zologis
Language:English (Spanish)
Published (Last):23 August 2015
PDF File Size:7.89 Mb
ePub File Size:13.40 Mb
Price:Free* [*Free Regsitration Required]

Quick Links. Download this manual. BiPAC Series. Table of Contents. Wireless adsl Page 2: Table Of Contents 1. Page 4 to target a machine on your network. Secondly, it can block and redirect certain ports to limit the services that outside users can access. For example, to ensure that games and other Internet applications will run properly, user can open some specific ports for outside users to access internal services in network.

It also supports rate management that allows ADSL subscribers to select an Internet access speed suiting their needs and budgets. Page 7 with on-line help. It also supports remote management capability for remote users to configure and manage this product. Page Chapter 2 2. Do not open or repair the case yourself. If the BiPAC Page The Front Leds 2. After the device is powered on, press it to reset the device or restore to factory default settings.

If they are not, verify that you are using the proper cables. Ensure that all other devices connected to the same telephone line as your Billion router e.

Page Chapter 3 If not, please refer to your Windows-related or other operating system manuals. Chapter In the Control Panel, double-click on Network Connections 2.

Double-click Local Area Connection. Page 17 Configuring PC in Windows 1. In the Control Panel, double-click on Network and choose the Configuration tab. Select the Obtain an IP address automatically radio button. In the Control Panel, double-click on Network and choose the Protocols tab.

Page Step-By-Step Installation 3. The Hardware Installation screen will appear. Four links are shown on the screen. Click them one by one and follow the guidelines to complete hardware installation. Page 21 4. Diagnostic screen. Click Next to enter Configuration Details 4. Page 22 8.

Please configure the Wireless LAN setting and click next. If your router does not support wireless, please ignore this screen and it will not appear. Page 23 Click Next to proceed to Diagnostic screen The IE browser will be opened automatically when you finish installing.

Page Factory Default Settings 3. Start IP Address: The default values are shown below. Chapter 4 Configuration Page Quick Start 4. It will guide you step by step to configure the password, time zone, and WAN settings of your device. Page 29 Step1. Set your new password. Step2: Choose your time zone Page 30 Step3: Set your Internet connection Page Interface Setup 4. Page 34 4. Page 35 this Device, you can totally setup 8 VCs on different encapsulations, if you apply 8 different virtual circuits from your ISP.

You need to activate the VC to take effect. Page 36 Choices vary depending on what you select in the Mode field. This option is typically used for Cable services. Please enter the Dynamic IP information accordingly. Page 37 Bridged IP in the Encapsulation field in the previous screen.

Page 38 4. Page 40 4. Wireless LANs can be as simple as two computers with wireless LAN cards communicating in a peer-to-peer network or as complex as a number of computers with wireless LAN cards communicating through access points which bridge network traffic to the wired LAN. If you do not have any wireless, both Page 42 increased security over WEP The default type of wireless is disabled and to allow all wireless computers to communicate with the access points without any data encryption Wireless MAC Address Filter The MAC filter screen allows you to configure the router to give exclusive access to up to 8 devices Allow Association or exclude up to 8 devices from accessing the router Deny Page 43 default key is key 1.

Pre-Shared key: The key for network authentication. The input format is in character style and key size should be in the range between 8 and 63 characters. Page Advanced Setup 4. Page 45 4. Gateway IP: IP address of the gateway or existing interface that this route uses.

The number need not be precise, but it must be between 1 and Page 47 4. Enabled: It activates your DMZ function. Select the SAVE button to apply your changes. Page 50 Rule Index: Choose the rule number. Note that port numbers do not change for the One-to-one NAT mapping type. This is equivalent to Many to One i. Enter 0. Page 52 4. But in some area, multimode cannot detect the ADSL line code well.

Type an IP address to restrict access to a client with a matching IP address. Page 54 4. URL Filter URL Index: This is item number. Windows does not support UPnP. Service Provider: www. E-mail Address: Type your e-mail address. Page 61 4. Page Maintenance 4. You can change the default password to ensure that someone cannot adjust your settings without your permission.

Every time you change your password, please record the password and keep it at a safe place. Page Time Zone 4. Choose your local time zone. After a successful connection to the Internet, the router will retrieve the correct local time from the SNTP server you have specified.

Page 64 To upgrade the firmware of BiPAC Series, you should download or copy the firmware to your local environment first. Page 65 DO NOT power down the router or interrupt the firmware upgrading while it is still in process. Improper operation could damage the router. Warning 4. Page 66 4.


Billion BiPAC 5200 Series User Manual

This article has been created to demonstrate how to configure your Billion BiPAC G router to connect to the internet. Open your preferred internet browser and type the address Click OK to continue. Click the Quick Start link at the top of the next page.


Billion 5200 User Guide



Billion BiPAC 5200G RC Manuals


Related Articles